Intel machine check architecture supported. Ok.Ĭalibrating delay using timer specific routine.

Memory: 744744k/1048448k available (1553k kernel code, 302496k reserved, 348k data, 116k init, 622464k highmem)Ĭhecking if this processor honours the WP bit even in supervisor mode. Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) PID hash table entries: 2048 (order: 11, 8192 bytes)ĭentry cache hash table entries: 65536 (order: 6, 262144 bytes) done.Įnabling unmasked SIMD FPU exception support. Ide_setup: ide_core.chs=0.0:980,16,32 - BAD OPTIONĮnabling fast FPU save and restore. Ide_setup: ide_generic.probe_mask=0x01 - BAD OPTION Kernel command line: -append ide_generic.probe_mask=0x01 ide_core.chs=0.0:980,16,32 auto nousb console=ttyS0,9600 bigphysarea=65536 ide1=noprobe no-hlt -net nic Nested traceback attempted via signal, from:Īnyone can help me to fix this issue, what seems to be the problem with my ASA i follow all the procedure but still came up to this problem below.

Panic: kernel - intr_establish: open interupt descriptor irq 15 Unable to open /proc/irq/15/irq error: Device or resource busy Ignoring PCI card in slot:6 (vendor:0x0 deviceid:0x0) Ignoring PCI card in slot:5 (vendor:0x0 deviceid:0x0) Ignoring PCI card in slot:4 (vendor:0x0 deviceid:0x0) Ignoring PCI card in slot:3 (vendor:0x0 deviceid:0x0) Ignoring PCI card in slot:2 (vendor:0x0 deviceid:0x0) Ignoring PCI card in slot:1 (vendor:0x0 deviceid:0x0) Ignoring PCI card in slot:0 (vendor:0x0 deviceid:0x0) I2c_read_byte_w_wait() error, slot = 0x4, device = 0xb0, address = 0 byte count = 1. * This product is for Cisco internal use ONLY!!! *

* WARNING WARNING WARNING WARNING WARNING WARNING WARNING WARNING * Welcome to LINA - ( F1-on-Linux platform ) desktop version! MKDIR failed No such file or directory for /var/log/ Then call your technical support representative.Īssertion '_vf_mode_init' failed: file 'vf_api.c', line 99Į1000: eth5: e1000_suspend: Error enabling D3 wakeĮ1000: eth5: e1000_suspend: Error enabling D3 cold wakeĮ1000: eth5: e1000_suspend: Error in setting power stateĮ1000: eth4: e1000_suspend: Error enabling D3 wakeĮ1000: eth4: e1000_suspend: Error enabling D3 cold wakeĮ1000: eth4: e1000_suspend: Error in setting power stateĮ1000: eth3: e1000_suspend: Error enabling D3 wakeĮ1000: eth3: e1000_suspend: Error enabling D3 cold wakeĮ1000: eth3: e1000_suspend: Error in setting power stateĮ1000: eth2: e1000_suspend: Error enabling D3 wakeĮ1000: eth2: e1000_suspend: Error enabling D3 cold wakeĮ1000: eth2: e1000_suspend: Error in setting power stateĮ1000: eth1: e1000_suspend: Error enabling D3 wakeĮ1000: eth1: e1000_suspend: Error enabling D3 cold wakeĮ1000: eth1: e1000_suspend: Error in setting power stateĮ1000: eth0: e1000_suspend: Error enabling D3 wakeĮ1000: eth0: e1000_suspend: Error enabling D3 cold wakeĮ1000: eth0: e1000_suspend: Error in setting power state Output of the show version command and the contents of the configurationįile. Copy the error message exactly as it appears, and get the Specifically, a programming assertion was

Gns3 asa lab config